CJ2305_CJ_MOSFETS_P-ch_0.35W_Parameters_ Price

CJ2305,CJ,MOSFETS

Attribute Name	Attribute Value
Manufacturer	CJ
Product Series	CJ-MOS
Product Type	MOSFETS
EU RoHS	Compliant(2011/65/EU)
EU REACH	Dose not contain REACH SVHC(1907/2006/EC)

Attribute Name

Attribute Value

Manufacturer

Product Series

CJ-MOS

Product Type

MOSFETS

EU RoHS

Compliant(2011/65/EU)

EU REACH

Dose not contain REACH SVHC(1907/2006/EC)

File Type	File Name
Data Sheet	cj2305_sot-23_2024.09.20.14.51.05.pdf

File Type

File Name

Data Sheet

cj2305_sot-23_2024.09.20.14.51.05.pdf

Product Recommendation Maker Dynamics Applications

Instructions for using silicon carbide (SiC) diodes When using silicon carbide (SiC) diodes, some safety factors should be taken into account, such as avoiding excessive current flowing through the diode to prevent damage. During use, attention should also be paid to circuit design and diode selection to ensure optimal system performance.

Voltage polarity and symbol diagram of MOS transistor, N-MOS and P-MOS The following text introduces the symbol rules for N-MOS voltage polarity and P-MOS voltage polarity respectively

Reverse Recovery Current and Electrical Test Item Vgs of Silicon Carbide (SiC) MOSFET The electrical testing item Vgs of SiC MOSFET mainly refers to the Gate Source Voltage. Reverse Recovery Current (Irr) refers to the current flowing through a diode during the reverse recovery process.

Photovoltaic inverters need to convert the direct current generated by solar panels into alternating current and output it to power loads such as water pumps. Therefore, devices that can withstand high voltage, high frequency, and high temperature are required. SiC devices have these characteristics, so it is possible to use SiC devices in photovoltaic inverters, but the specific use needs to be comprehensively considered based on the actual situation.

The requirements for the driver board of SiC silicon carbide MOS dual pulse testing equipment are as follows: The requirements for the driver board of SiC silicon carbide MOS dual pulse testing equipment are as follows:

Calculation methods for P-channel enhanced VDS and CGS In a P-channel Enhanced Mode FET, VDS represents the voltage between the drain and source, while CGS represents the capacitance between the gate and source. When calculating VDS, it is necessary to consider the working state of the P-Channel Enhanced Mode FET. Generally, the following formula can be used for calculation:

Detailed explanation of reverse recovery principle of silicon carbide (SiC) diode Silicon carbide diodes are unipolar devices, so compared to traditional silicon fast recovery diodes (silicon FRDs), silicon carbide diodes have ideal reverse recovery characteristics. When the device switches from forward to reverse blocking direction, there is almost no reverse recovery power, and the reverse recovery time is less than 20ns. Even the reverse recovery time of 600V10A silicon carbide diodes is less than 10ns.

The Development Trend of High Voltage SiC MOSFET The research on high-voltage SiC MOSFETs is gradually deepening, mainly focusing on the design, preparation, and detection of high-voltage SiC MOSFETs. In the past two years, Sic Mosfet has broken through the peak tunneling voltage of 2600V, with crystal surface insulation characteristics as high as 200MV • cm-1, and static performance reaching 500A/1700V for a single chip in a half bridge topology. It can also support constant current and constant voltage regulator operation. In addition, there are SiC Mosfets designed for solid-state dye solar energy to meet the needs of these applications.

Introduction to SiC Silicon Carbide MOSFET Devices SiC devices are a new type of silicon-based MOSFET, especially SiC power devices with higher switching speed and wider output frequency. SiC power chips are mainly composed of MOSFETs and PN junctions.

Analysis of Silicon Carbide (SiC) Technology Barriers: What are the Silicon Carbide Technology Barriers Groove type silicon carbide power devices have greater manufacturing difficulty. According to the different device structures, silicon carbide power devices can be mainly divided into planar devices and trench devices. Flat silicon carbide power devices have good unit consistency, simple manufacturing process, but are prone to JFET effect and have high parasitic capacitance and on state resistance. Compared to planar devices, groove type silicon carbide power devices have lower unit consistency and more complex manufacturing processes. However, the groove structure is beneficial for increasing device unit density, reducing the occurrence of JFET effect, and solving the problem of low channel mobility. It has excellent performance such as low on resistance, low parasitic capacitance, and low switching energy consumption, and has significant cost and performance advantages. It has become the mainstream direction of silicon carbide power device development.

Product number： {{currentProduct.code}}

Product information： {{currentProduct.descCn}}

Order quantity： {{currentProduct.num}}

Cart （{{myCartItems.length}}Item）

Total amount：

Product number：	MOS-MPM0360W35M14F1201CJ
Manufacturer Product Number：	CJ2305
Manufacturer ：	CJ
Series ：	CJ-MOS
Product Type ：	MOSFETS
Configuration ：	P-ch
Power Dissipation (PD) ：	0.35W
Continuous Drain Current (ID) ：	-4.1A
Drain-Source Voltage (V) ：	-12V
Package ：	SOT-23
Description：	MOS ,P-ch ,CJ2305 ,0.35W ,-4.1A ,-12V ,SOT-23

CJ2305,CJ,MOSFETS

CJ2305

Series Introduce Find Similar

Series Introduce Find Similar

File

Product Recommendation Maker Dynamics Applications

Product Recommendation Maker Dynamics Applications

Product Recommendation Maker Dynamics Applications

{{ isChinese?level2Category.viewNameCn:level2Category.viewNameEn }}

CJ2305,CJ,MOSFETS

CJ2305

Series Introduce Find Similar

Series Introduce Find Similar

File

Related Series

Product Recommendation Maker Dynamics Applications

Product Recommendation Maker Dynamics Applications

Product Recommendation Maker Dynamics Applications