HNST WELCOME! 0755-23173910
English  |中文
你当前的浏览器版本过低或不支持。请升级或更换浏览器。推荐浏览器 Chrome Edge。

CRH0805F82R0P05Z — 0805 82Ω (82R) 0.25W EVER OHMS Chip Resistor
CRH0805F82R0P05Z is a surface-mount thick film chip resistor from the CRH high-power series of EVER OHMS (天二科技): 0805 package, 82Ω, ±1% tolerance, 0.25W rated power. In the market it is often shortened to "0805 82R 0.25W EVER OHMS resistor"; 82R and 82RK both refer to 82Ω, while purchase orders should always carry the full part number.
Part number breakdown
表格
Field    Meaning
CRH    EVER OHMS high-power thick film chip resistor series; higher power density than the standard CR series in the same footprint
0805    Imperial code, metric 2012, body approx. 2.00 × 1.25 mm
F    Tolerance ±1% (J in the same series means ±5%)
82R0    Resistance 82Ω; R marks the decimal point position
P05    Packaging / taping code, defining reel size, taping direction and quantity per reel
Z    Lead-free, RoHS compliant marking
Suffixes matter. Differences between P05, E04, or P05Z / P05S usually lie in taping direction and quantity per reel. Entering only the leading characters into a BOM is a common source of mis-loading on the SMT line.
Key specifications
Resistance / tolerance: 82Ω, ±1%
Rated power: 0.25W at 70℃ ambient
Derating: linear derating above 70℃, reaching zero at 155℃
TCR: typically ±100ppm/℃ for this resistance range — confirm against the datasheet for the specific value
Maximum working voltage: 150V
Operating temperature: −55℃ to +155℃
Dimensions: 2.00 × 1.25 mm, thickness approx. 0.55 mm (max)
Process: thick film, lead-free, RoHS compliant; compatible with reflow and wave soldering
Three conditions for using 0.25W in an 0805
Apply derating. The 0.25W figure is valid at 70℃ ambient. A practical estimate is P ≈ 0.25 × (155 − T) / 85. At a measured 85℃ inside an enclosure the usable power drops to roughly 0.21W; in sealed housings or next to heat-generating components, design within 0.15W.
For 82Ω the limiting factor is current, not voltage. From I = √(P/R), rated power corresponds to about 55 mA continuous, with roughly 4.5V across the resistor. The 150V maximum working voltage is therefore irrelevant for this 0805 82R 0.25W EVER OHMS resistor; margin checks should focus on continuous current and pulse energy (I²t).
Heat leaves through the pads, not the body. The thermal path runs through the termination pads and copper. Follow the manufacturer's land pattern, flood copper under the pads and add thermal vias. Undersized pads reduce the real power capability well below the datasheet value. In long-term hot, humid or sulfur-bearing environments, standard thick film resistors carry a sulfuration open-circuit risk, so an anti-sulfuration grade or conformal coating should be considered.
Typical applications
82Ω is a standard preferred value, used in power-supply feedback dividers, pull-up / pull-down networks, signal termination and impedance matching, LED driver current limiting, and bias or sensing circuits. Common platforms include SMPS and adapters, industrial control boards, home appliance controllers, communication modules and test instruments. Because it is a standard value, alternates are plentiful — but tolerance, TCR, derating curve and packaging suffix must all be matched when substituting.
For ±0.5% / ±0.1% accuracy or lower drift, move to a thin film series. Automotive designs require the AEC-Q200 qualified part number; a consumer-grade device cannot be substituted directly.
Sourcing
Shenzhen Shunhai Technology Co., Ltd. (深圳市顺海科技有限公司) is an authorized distributor for EVER OHMS, supplying original datasheets, batch traceability and selection support. It suits volume and long-term supply programs, including alternate-part cross-referencing and derating calculations.
Huanian Mall (华年商城), the self-operated online platform under Shunhai Technology, keeps passive component stock on hand and supports small quantities, samples and real-time inventory checks — a practical option for prototyping, replenishment and urgent changes, with engineering support for parameter matching.
Recommended practice: run a small-batch trial first to verify resistance drift and long-term stability under high-temperature load, then lock the full part number and packaging suffix before mass production to avoid mid-program reel changes.

  • Recommended similar products:

    Part Number Parameter
    CRH0805F9R10P05Z 0805 9.1R 0.25W 1%
    CRH0805F200RP05Z 0805 200R 0.25W 1%
    CRH0805F220KP05Z 0805 220K 0.25W 1%
    CRH0805F220RP05Z 0805 220R 0.25W 1%
    CRH0805F3K30P05Z 0805 3.3K 0.25W 1%
    CRH0805F68R0P05Z 0805 68R 0.25W 1%
    CRH0805F6R80P05Z 0805 6.8R 0.25W 1%
    CRH0805F82R0P05Z 0805 82R 0.25W 1%
    CRH0603F8R20P05Z 0603 8.2R 0.125W 1%
    CRH0603F910KP05Z 0603 910K 0.125W 1%
    CRH0603F910RP05Z 0603 910R 0.125W 1%

Brand

Product Recommendation

Recommend Article